Carbon Dioxide Balance of Wood Substitution: Comparing Concrete- and Wood-Framed Buildings

In this study a method is suggested to compare the net carbon dioxide (CO₂) emission from the construction of concrete- and wood-framed buildings. The method is then applied to two buildings in Sweden and Finland constructed with wood frames, compared with functionally equivalent buildings constructed with concrete frames. Carbon accounting includes: emissions due to fossil fuel use in the production of building materials; the replacement of fossil fuels by biomass residues from logging, wood processing, construction and demolition; carbon stock changes in forests and buildings; and cement process reactions. The results show that wood-framed construction requires less energy, and emits less CO₂ to the atmosphere, than concrete-framed construction. The lifecycle emission difference between the wood- and concrete-framed buildings ranges from 30 to 130 kg C per m² of floor area. Hence, a net reduction of CO₂ emission can be obtained by increasing the proportion of wood-based building materials, relative to concrete materials. The benefits would be greatest if the biomass residues resulting from the production of the wood building materials were fully used in energy supply systems. The carbon mitigation efficiency, expressed in terms of biomass used per unit of reduced carbon emission, is considerably better if the wood is used to replace concrete building material than if the wood is used directly as biofuel.     

Effect of soil solids concentration in batch tests on the partition coefficients of organic pollutants in landfill liner-soil materials

 The effect of the soil solids concentration in batch tests on the measured values of the partition coefficient (K _p) of organic pollutants in landfill liner-soil material was investigated. Since this study was based on the results of batch and column tests conducted independently, there were limitations to the conclusions derived. The organic compounds tested were benzene, methylene chloride, toluene, trichloroethylene, and p-xylene. The results of this study showed that as soil solids concentrations increased, the measured K _p values of these organic compounds strongly decreased. The observed values of K _p stabilized when the soil solids concentration was above a certain value. Typical K _p values obtained from batch tests conducted under high soil solids concentrations were close to those obtained from column tests. It was concluded that the K _p values of organic compounds measured under low soil solids concentrations, i.e., less than 100 g/l, may not correctly simulate the field situation. Consequently, the values of K _p obtained with low soil solids concentrations can result in an overestimation of the retardation factor of the landfill liner material. Received: March 14, 2002 / Accepted: August 25, 2002     

STREAM DISCHARGE PREDICTION VIA A GRID BASED SOIL WATER ROUTING WITH PADDY FIELDS1

ABSTRACT: A grid based daily hydrologic model for a watershed with paddy fields was developed to predict the stream discharge. ASCII formatted elevation, soil, and land use data supported by the GRASS Geographic Information System are used to generate distributed results such as surface runoff and subsurface flow, soil water content, and evapotranspiration. The model uses a single flow path algorithm and simulates a water balance at each grid element. A linear reservoir assumption was used to predict subsurface runoff components. The model was applied to a 75.6 km² watershed located in the middle of South Korea, and observed stream flow hydrographs from 1995 and 1996 were compared to model predictions. The stream flow predictions of 1995 and 1996 generally agreed with the observed flow, resulting in a Nash‐Sutcliffe efficiency R² of 0.60 and 0.62, respectively. The hydraulic conductivity for percolating water through the saturated layer affected baseflow generation. The levee height of the paddy influenced the time and magnitude of the surface runoff, depending on irrigation management. The model will be used for making low flow management decisions by evaluating the role of each land use to stream flow, especially in case of paddy decrease by gradual urbanization of a watershed.     

Design of a representative and cost-effective sampling programs for industrial wastewater with examples from bleached kraft pulp and paper mills

The diagram constructed for selection of sampling methods indicates that, for a systematic error, E ≤ 13%, grab sampling (GS) may be used to characterize effluents with variation coefficient of flow ≤ 120% and of contaminant concentrations ≤ 10%. For the whole studied range of variation coefficient of contaminant concentrations (2–82%), time-proportional compositing (TC) method may be applied with E ≤ 10% for effluents characterized by variation coefficients in flow < 90%. The more complicated flow-proportional compositing (FC) method is required only for effluents with larger variation coefficients or to produce more precise results. The diagram constructed for selection of sampling frequencies indicates that sequential sampling at intervals of approximately 60 min may be applied with E ≤ 10% for effluents characterized by variation coefficients ≤ 30%. Practical application of the diagrams, constructed using normal series, was checked against monitoring data from two pulp and paper mills in Vietnam. The two diagrams provided results on sampling methods and frequencies in good agreement with those obtained from actual monitoring data with percentages of agreement cases of 80 and 75%, respectively. The approach was applied in design of a monitoring program at the Bai Bang integrated pulp and paper mill in Vietnam.     

Characteristics of large cooking oil pool fires and their extinguishment by water mist

Large cooking oil pool fires, occurring in industrial oil cookers, present a severe hazard to food processing plants due to their size and the large amount of hot oil involved. This paper reports a series of full-scale fire experiments conducted in a large industrial oil cooker mock-up. The characteristics of large cooking oil pool fires and the effect of oil depth and hood position in the oil cooker on fire growth were studied. The use of water mist for extinguishing large oil pool fires and their extinguishing performance under different discharge pressure and with different types of water mist systems were investigated. Experimental results showed that the cooking oil underwent a substantial expansion in volume during heating. The fires developed quickly once the oil auto-ignited. The fire growth rate was affected by the oil depth in the pan and the hood position in the oil cooker. The water mist fire suppression systems effectively extinguished large cooking oil fires and prevented them from re-igniting. Their extinguishing performance was determined by the type of water mist system, discharge pressure and hood position in the oil cooker.     

Current status and research on E-waste issues in Asia

Rapid economic growth in Asia and the increasing transboundary movement of secondary resources will increasingly require both 3R endeavors (reduce, reuse, recycle) in each country and appropriate control of international material cycles. Recently, managing electrical and electronic waste (E-waste) has become an important target for domestic and international material cycles from the viewpoints of environmental preservation and resource utilization efficiency. To understand the current status of E-waste issues in the context of international material cycles and to discuss the future tasks related to achieving 3R in the region, we organized the National Institute for Environmental Studies (NIES) E-waste Workshop in December 2004. This article reviews past studies on E-waste and briefly describes the topics presented and discussions held at the workshop. The topics at the workshop included E-waste generation, recycling systems, international trade, and environmental impacts. In addition, we discussed various issues such as terminology, current environmental concerns, and possible solutions. Transboundary shipments of E-waste should be conducted taking into consideration the concept of sustainable development. The direction of future research and possible collaborations are also discussed.     

Accelerated soil dissipation of tebuconazole following multiple applications to peanut

Repeated application may increase rates of pesticide dissipation in soil and reduce persistence. The potential for this to occur was investigated for the fungicide, tebuconazole (alpha-[2-(4-chlorophenyl)ethyl]-alpha-(1,1-dimethylethyl)-1H-1,2,4-triazole-1-ethanol), when used for peanut (Arachis hypogaea L.) production. Soil samples were collected from peanut plots after each of four tebuconazole applications at 2-wk intervals. Soil moisture was adjusted to field capacity as necessary and samples were incubated in the laboratory for 63 d at 30 degrees C. Untreated plot samples spiked with the compound served as controls. Results indicated accelerated dissipation in field-treated samples with the time to fifty percent dissipation (DT50) decreasing from 43 to 5 d after three tebuconazole applications. Corresponding increases in rates of accumulation and decay of degradates were also indicated. Best-fit equations (r2 = 0.84-0.98) to dissipation kinetic data combined with estimates of canopy interception rates were used to predict tebuconazole and degradates concentration in soil after each successive application. Predicted concentrations compared with values measured in surface soil samples were from twofold less to twofold greater. Use of kinetic data will likely enhance assessments of treatment efficacy and human and ecological risks from normal agronomic use of tebuconazole on peanut. However, the study indicated that varying soil conditions (in particular, soil temperature and water content) may have an equal or greater impact on field dissipation rate than development of accelerated dissipation. Results emphasize that extension of laboratory-derived kinetic data to field settings should be done with caution.     

Biodegradability of algal-derived organic matter in a large artificial lake by using stable isotope tracers

In order to understand the biodegradability of algal-derived organic matter, biodegradation experiments were conducted with ¹³C and ¹⁵N-labeled natural phytoplankton and periphytic algal populations in experimental conditions for 60 days. Qualitative changes in the dissolved organic matter were also determined using parallel factor analysis and the stable carbon isotopic composition of the hydrophobic dissolved organic matter through the experimental period. Although algal-derived organic matter is considered to be easily biodegradable, the initial amounts of total organic carbon newly produced by phytoplankton and periphytic algae remained approximately 16 and 44 % after 60 days, respectively, and about 22 and 43 % of newly produced particulate nitrogen remained. Further, the dissolved organic carbon derived from both algal populations increased significantly after 60 days. Although the dissolved organic matter gradually became refractory, the contributions of the algal-derived organic matter to the dissolved organic matter and hydrophobic dissolved organic matter increased. Our laboratory experimental results suggest that algal-derived organic matter produced by phytoplankton and periphytic algae could contribute significantly to the non-biodegradable organic matter through microbial transformations.     

Hydro-thermal reaction according to the CaO/SiO2 mole-ratio in silico-manganese slag

Journal of Material Cycles and Waste Management - SiMn slag is a by-product of the production of ferroalloy, and has a chemical composition that could be used as a cement admixture. It is not...